Mending my mistakes

-
While I am not a king (inside joke for Spaniards only) I do make mistakes quite often. One of them was not to disconnect my RAMPS-controlled 3D printer from the computer and mains supply for a quick solder job (just one pin of heating resistor was loose just before starting a print ...). Unfortunately, my trustry JBC solder of the last twenty years was not properly isolated anymore and I had a big flash and all the house lights went down.

When I restored the power the computer was booting up happily, the printer power supply light was on but the printer was dead and the computer was unable to detect the printer anymore. All the lights on the board and on the Arduino Mega were off too and my system shown a warning message that USB port was disconnected for excessive power consumption: no good news at all, but at least I learned the USB port was not completely dead.

I removed the RAMPS board from the Arduino Mega, connected it to the USB cable and then the lights come back on, surprisingly RX and TX leds too. But my computer did not detect any connection or disconnection on the USB. Of course Arduino IDE was incapable of doing anything else. The board seemed dead. But I had lying on my desk an Sparkfun FTDI Basic board, and when I connected the RX and TX and GND pins to my USB powered Arduino Mega I was able to upload the Blink test program and it worked. That proved the ATMega  microcontroller was not dead. So I decided to replace the FTDI chip, something I have never done before. The process was quite straightforward:

Fist I took an old Arduino board from my junk box:
Next I used a heat gun to heat up the FTDI chip area and when I thought it was warm enough I turned the board upside down and gravity did the rest:
I could not do the same with my Mega board as many other SMD components were close to the damaged FTDI chip, so I use some tweezers to pull from the chip while I heated it up with the heat gun (this is likely a better way):
Being careful of not confusing the damaged and the savaged FTDI chip I took the latter and I let it rest on the Mega board while heating it gently till I could see the chip seating in its place while the solder became liquid again (unfortunately I damaged some of the pins of the digital inputs header):
The Arduino Mega board is now back to life and after diagnosing a couple of damaged Pololu drivers in the RAMPS board I hope everything would be back to square one soon.

What is no longer with us and it is gone for good is my good old soldering iron. 

Note to self: Remember to power down everything you plan to solder, even if it is just tiny bit.




Comments

Post a Comment

Popular posts from this blog

VFD control with Arduino using RS485 link

-
Image
Variable Frequency Drives ( VFD ) allow the control of spindles so speed can accurately be controlled and a detailed acceleration profile for the spindle and reverse rotation can all be handled. In essence a VFD is an three phase inverter for three-phase AC motor. I am using a popular (I mean cheap) Chinese VFD and though the reference manual is not great, I could see there is a built-in RS-485 port. I usually control the start, stop and speed selection using the keyboard on the unit but I thought it will be more useful if I could control everything from the same Arduino is doing our CNC table control. Some cheap RS-485 off eBay and some lines of code later, I can start, stop and change the speed from an Arduino. What a cool thing to have! Some configuration of your VFD are needed before you can use it like that.  You need to set PD163=1 (I am using address 1 in the code). PD=164=1 (for setting serial to 9600bps) and PD165=0 (for using ASCII and 8N1 character format)
Read more

How to get sinusoidal s-curve for a stepper motor

-
Image
After some experimentation, and delving a bit into the math of motion, I realized there can be a significant difference on the motion of a machine by just making small changes. A common and popular approach to smooth one axis of motion is to use a trapezoidal speed pattern, where acceleration and deceleration are uniformly accelerated movements (aka constant acceleration motion) separated by a portion happening at cruising speed. The problem comes with the fact that, while that approach is simple to understand and to code, it does contain sudden changes in the acceleration, that show as spikes on the acceleration derivative, called jerk. These sudden changes in the acceleration translate into undesired vibration in our machines. Most of that can be eliminated by selecting a motion pattern that does not contain sudden changes of acceleration. If we chose a mathematical function for our speed whose second derivative is continuous, then we reduce system vibration quite a lot. One ma
Read more

Stepper motor step signal timing calculation

-
Image
While we use stepper motors in many devices, the timing of the step signals is not always well understood. Most of us can see how a fixed speed is a bad idea unless the speed of motion is really slow, but it is fixed speed what is really to generate with simple code. You just can use the Arduino Blink example to send a fixed frequency of pulses to a stepper motor driver. If too slow, just reduce the delay value. But for most real-life applications variable speed controls will perform better. These systems will speed up the motor to a given maximum speed and it will slow it down to stop at the desired step count. But understanding the math behind this process is sometimes not obvious. Let us start with the simple case of the so-called trapezoidal speed motion profile. Here motion takes place in three phases: acceleration, constant speed (cruising) and deceleration. But the point is how can our code create such a behavior. Stepper motor drivers usually accept two signals to control
Read more